Craft Closet #3

My DW had the opportunity to start outfitting her craft and sewing centers. The pegboard works really well, giving her a lot of flexibility in how she sets the areas up. Here is a picture of the craft closet...


I took extra care to hang the pegboard with the holes lined-up horizontally, so we could use it to mount adjustable shelving in the 1/4" holes. Since the pegboard is fairly thin, I added a few support screws the shelf brackets to make sure they were sturdy.

Here is the sewing closet. My DW is just in the process of setting this up.


I need to add some task lighting under the shelves this weekend to keep the shadows off of the work surfaces.

All craft center posts

Craft Closet #2

We were able to get the theater room and craft closets textured, primed and ready for paint. I installed the counter tops as shown below. The black counter with the green painted pegboard actually looks good (I never thought I would say peg board looked good...)


Notice the two layers of trim at the top. The ceiling in the closet is 1 1/4" out of level due to the house sagging over the years. The stone fireplace upstairs was not adequately supported (now it is), causing the sag. The lower layer of trim is even with the pegboard holes and the upper layer is partially cut to match the ceiling. It also runs a bit out of level, splitting the difference. All this together effectively hides the out-of-level condition, especially once the closet doors are added.

We bought the laminate counter piece at Home Depot - $78 for an eight foot piece. The other half went to the other craft closet (one for sewing, one for stamping, paper crafts, etc.) It seems like a nice high quality surface, with a fully wrapped front. I cut it with a new carbide saw blade on the table saw, and had no chip-out.


My DW will keep her sewing machine and surger on this counter, so they will always be ready to use. To keep the counter from sagging over time under the constant weight, I added these heavy duty shelf supports (rated at 400 lbs). I quickly painted the wood backup pieces once I installed them, which helps me avoid extra masking. I also glued and screwed a fir 1x4 across the front behind the counter lip.


Next I need to make a couple of shelves for the top of the closet and 3 drawers that go under the counter. After that, my DW will get all the pegboard stuff.

Craft Closet #1

After watching a Martha Stewart segment on pegboard organizers my DW decided she wanted pegboard in the craft closet and sewing center I am building for her. The craft closet (4' x 5') is located at the entrance to our home theater as shown in the diagram below. The sewing center is on the other side of the basement.

We decided to focus on the storage areas of the basement remodel before completing the home theater, so we can get all the remaining stuff that is stacked in the room put away. Also, I am not 100% settled on all the theater room details, and this will give me time to work them out.

Here is a picture of the craft closet before installing pegboard. Why do all this sheetrock work if you just going to install pegboard over it? Two reasons: sound management and fire resistance. The sheetrock walls of this and the opposing closet are sound absorbers, stopping the noise from the theater traveling to the rest of the living areas. So far the sound reduction has been great, and the sheetrocked partition walls obviously contribute to this a lot. Also, even on a simple partition wall internal to the house, its best to sheetrock and tape it to help reduce airflow in case of fire. I could not find a specific requirement for it in this case, but it's always a good idea.



In this photo, the pegboard is being installed. I have a system that includes a support ledger and battens to mount the pegboard. The 1/2" battens provide room for the hooks. I used OSB that I cut into strips, which is significantly less expensive than using furring strips. I can cut 30 OSB strips for the cost of 5 1x2 furring strips (in about 15 minutes). Also, OSB is a greener option, since it's made from wood chips, not full lumber.



Here is a simple diagram showing how the pegboard is mounted. The lower ledgers will also provide support for the work surfaces I am installing later.


Here is the sewing center with the ledgers installed. Note that I have a top ledger as well. This is because the pegboard will not go all the way to the ceiling here, and I need a surface to nail the top trim to.


This next photo shows the battens installed. These are nailed directly to the studs behind the sheetrock. I also glued them with wood glue.

Note that I put small batten supports around the outlet boxes. I am going to need to add electrical box extenders to bring the face of the box even with the pegboard. I am definitely not in favor of just bringing the outlets out the surface and leaving a gap. This exposes combustible material to open wiring, which is a code violation and just plain hazardous. A few extra dollars and minutes are not a big deal.


Finally, here is the pegboard installed. I now need to trim it out before my DW paints it. The corners came out very tight, so I am only caulking these. Once painted, I will install the work surface.


I have to admit that I initially thought the idea of pegboard was crazy. I reminds me of some musty garage workbench. However, after doing a bit of research to make sure I could provide what my DW wanted, I realized there are a lot of cool accessories out there, and the overall flexibility is great.